Univex MAX 8512 Bedienerhandbuch

INSTRUCTION 8512 MANUAL MAX SERIES Slicer WE THANK YOU FOR YOUR PURCHASE OF OUR MODEL 8512 SLICER. 8512/498 EDS

8512 REPAIR INSTRUCTIONS (including disassembly, replacement and reassembly) KNIFE (Removal) (Figure 3) 1. WARNING Disconnect electrical power cord. 2

8512 E. Remove lama by turning counter-clockwise. F. Push knife support assembly from bottom and remove. 2. GEAR REPLACEMENT A. With knife support ass

8512 ELECTRICAL ASSEMBLY 1. WARNING DISCONNECT ELECTRICAL SUPPLY 2. Remove four rubber feet (Fig. 2 [24]) and 4 extension legs (Fig. 2 [52]). 3. Remov

8512 BASE ASSEMBLY Figure 2 ILLUS. NO. PART NO. DESCRIPTION QTY. 1. 8512300A SUPPORT, CARRIAGE, ALSO FIG. 4 [6] 1 2. 6509098 SET SCREW, M6-1.0

8512 BASE ASSEMBLY Figure 2 (CONT.) ILLUS.NO. PART NO. DESCRIPTION QTY. 49. 8512835 PULLEY (For 115V/100V) 1 8512835A PULLEY (For 220V) 1 5

8512 CASTING and BLADE ASSEMBLY Figure 3 ILLUS. NO. PART NO. DESCRIPTION QTY 1. CASTING 1 2. 8512203 PIN 2 3. 8512215 SEAL 1 4. 8512216 SE

8512 CASTING and BLADE ASSEMBLY Figure 3 Page 15

8512 ARM ASSEMBLY Figure 4 ILLUS. NO. PART NO. DESCRIPTION QTY. 1. 7510038 RUBBER SHOCK ABSORBER 2 2. 8512314 SPRING, DAMPER 1 3. 8512313 SC

8512 SLICE CONTROL ASSEMBLY Figure 5 ILLUS. NO. PART NO. DESCRIPTION QTY. 1. 7510067 BOLT, SOC HD CAP M6-1.0 X 20MM 2 2. 8512527 BOLT, HEX HD M

8512 CARRIAGE ASSEMBLY Figure 6 ILLUS NO. PART NO. DESCRIPTION QTY. 1 8512432 SPACER, ADJUSTMENT 1 2 8512437 STUD & KNOB, ADJUSTMENT SPACER

8512 TABLE OF CONTENTS DESCRIPTION PAGE Table of Contents 1 List of Illustrations 1 Introduction 3 Installation Instructions 3 Safety Warnings 3

8512 SHARPENER ASSEMBLY Figure 7 ILLUS NO. PART NO. DESCRIPTION QTY. 7510151 SHARPENER ASSEMBLY WITH COVER 1 6509153 KNOB, COVER 1 2 65091

8512 ELECTRICAL ASSEMBLY 115v, 60hz, 1ph 220v, 50hz, 1ph Figure 8 ILLUS. NO. PART NO. DESCRIPTION QTY. 1. 8512844 MOTOR, 115V, 60HZ, 1PH, 1/2HP,

8512 ELECTRICAL ASSEMBLY Figure 8 Page 21

8512 SCHEMATIC 115V, 60HZ, 1PH 100V. 50/60HZ, 1PH Figure 9 Page 22

8512 SCHEMATIC 220V, 50HZ, 1PH FIGURE 10 Page 23

8512 OVERALL VIEW OF MEAT SLICER MODEL 8512 Figure 1 1 INDICATOR LIGHT 9 CARRIAGE ARM 2 ON-OFF SWITCH 10 ELECTRIC CORD 3 FENCE 11

8512 INSTRUCTION MANUAL INTRODUCTION This manual contains instructions for the Installation, Operation, Care, Maintenance and Repair of the Meat Slici

8512 OPERATION INSTRUCTIONS The Univex slicer is designed to meet the cook's demand for an efficient, sturdy slicer. The Univex slicer will give

8512 3. The knife cutting area should be clean and free from food, especially grease. Grease will ruin the ability of a grinding stone to sharpen an e

8512 Never use detergents nor wash the slicer or any of its parts is a dishwashing machine or the clear protective finish will be damaged. Warning

8512 LUBRICATION INSTRUCTIONS A = Clean and apply mineral oil weekly. C = 140 WT USDA oil. Change when changing gears B = Apply Petro-Gel (4400408)

8512 TROUBLESHOOTING GUIDE TROUBLE POSSIBLE CAUSE REMEDY 1. Slicer will not operate. 1.1 Electrical service down. 1.2 Burned switch contacts. 1.3 M